The first-line raw material storage and transportation system of our company adopts Φ1.6m × 8.5m pneumatic lift pump, which is supplied by 3 Roots blowers. In this paper, the phenomenon of blocking material appeared in the use of pneumatic lift pump is analyzed and the solution is found out.
1, Roots blower fan failure
1.1, Roots blower outlet relief valve pressure setting is too small
Trial production early, with the amount of mill feed increased, appear to enhance the pump blocking material. Roots blower current value of about 65%, is a normal range, but Roots blower outlet safety valve exhaust. On-site pipeline barometer readings did not reach the safety valve emptying pressure 80kPa. Re-adjust the safety valve pressure screw, such blocking material can be ruled out.
1.2, Roots blower belt off or burning
In the V-belt wear or aging when the new triangle tension is not suitable, easy to make the V-belt off or burn. For example, the central control room screen shows a Roots blower current value dropped from about 70% of normal to no-load current 40%, while the other two Roots blower current from about 70% to 80%. In the control room did not pay attention to this alarm, switching standby Roots blower is not timely, leading to the pneumatic lift pump blocking material. The on-site inspection revealed that the safety valves on the outlet pipes of the three Roots blowers were all exhausted outward. The triangle of the first Roots blower was dropped off or burnt out, causing the motor to run idle, resulting in an increase in the current of the other two blowers. Switching to a backup Roots blower solves the problem.
1.3, Roots blower outlet check valve spool off, closing valve disc wear
Roots blower outlet check valve role is to prevent the pressure air flow back to the rotor cavity after the fan down. Globe valve pneumatic control, open before the fan motor operation, shut down after the motor shutdown, cut off the anti-channeling pressure air flow. Due to the cut-off valve wear and tear of the valve plate, resulting in pressure flow from the gap anti-channeling, impact check valve spool, a long time, resulting in spool off. The blocking phenomenon caused by such causes is as follows:
The control room screen shows three Roots blower current value from the normal value of about 70% of the peak instantly dropped to no-load current about 40%. On-site inspection of gas lift pump blocking material, but 3 Roots blower safety valve does not exhaust. Air flows from the failed Roots blower through the exhaust pipe, rotor chamber to the suction line. Stop the Roots blower, the shut-off valve is closed, the other two Roots blower current value instantly increased from 40% to 80%, safety valve exhaust.
2, pneumatic lift pump damaged canvas layer, air chamber material
After the canvas is damaged, the raw material fed into the pneumatic lift pump can not be well vaporized, reducing the conveying capacity of the pump. When the feeding amount exceeds the conveying capacity of the pump, blocking occurs. 3 Roots blower fan current values are about 80%, safety valve deflated.
Approach: no need to stop immediately replaced, usually wait until the shutdown and then replace the canvas. On-site treatment may not need to open the pump body manhole door to discharge material, just open the big raw material warehouse top bag dust removal exhaust fan inlet valve, and at the same time chooses to open 3 Roots blowers to pump the material in the body to the air.
3, incoming wet caking
Due to material factors leading to the airlift pump plugging material is mainly caused by moisture, especially wet end of the humidification tower blocking material, clear down the wet material into the pneumatic lift pump by the screw conveyor, can not be vaporized away. The control room showed 3 Roots blower current values are about 40% of the no-load current, the safety valve does not deflate, but the feed chute is diffuse material, percussion pump body, sound dull.
Approach: Stop raw mill system, open the pump manhole, manual shoveling, clear canvas layer and then reboot.
What are CNC Plasma Cutting Machines?
Plasma cutting is a process that cuts through electrically conductive materials by means of an accelerated jet of hot plasma. Typical materials cut with a plasma torch include steel, Stainless steel, aluminum, brass and copper, although other conductive metals may be cut as well. Plasma cutting is often used in fabrication shops, automotive repair and restoration, industrial construction, and salvage and scrapping operations. Due to the high speed and precision cuts combined with low cost, plasma cutting sees widespread use from large-scale industrial CNC applications down to small hobbyist shops. CNC cutting machines, such as CNC plasma cutting machines, utilize their intricate software systems and components to efficiently, accurately and smoothly handle plasma cutting processes.
CNC Plasma Cutting vs. Other Cutting Methods:
Another cutting method utilizing CNC machines is oxy-fuel, using fuel gases and oxygen, which dates back about 100 years. Here, a stream of oxygen is blasted onto a metal heated to kindling temperature, turning it into a flowing metal oxide.
With CNC plasma cutting machines, a plasma torch blows an inert gas at high speeds out of a nozzle, through an electrical arc, which turns some of that gas to plasma.
While all of these options remain widely used today, CNC plasma cutting machines are typically seen as a solution for manufacturers who are concerned with quickly and efficiently cutting conductive materials up to 3″ thick. The CNC plasma cutting process has superior cutting speeds, piercing speeds, and generates very precise cut qualities. More speed and higher quality also produces superior efficiency and productivity.
Cnc Plasma Cutting Machine applications:
CNC plasma cutting machine features:
2.START control system
3.Huayuan 120A plasma generator(Optional: Hypertherm power supply)
4.Cutting Material Collection Box with wheels,for easy take out products
5.High Quality cut performance,Fast cutting speed,high precision and low cost.
6.With firm and reasonable structure,the machine is easy to operate and durable for use.
7.The cutting incision is thin and tidily and can avoid the second processing.
8.High configurated CNC system,auto arc-striking and stable performance.
9.Working with computer and support G code and files of Uncannest software (specilized in cutting metal material) (optional Fastcam software)
10.It can cut metal plate of advertising 3D lighting letter and flute profile letter with high cutting precision.(USA power is optional)
Effective Cutting Width (X axis) 1500mm optional Effective Cutting Length (Y axis) 3000mm optional Feature Dustproof design and heavy duty frame Drive Mode Leadshine Rail Taiwan inported Hiwin Square rail Lifting body 1set Plasma torch 1set File transmission USB transmission Cutting shape Able to program and cut the steel plate parts with any plane shapes formed by straight lines and arcs; Software Fastcam Software Plasma power source Huayuan 63A 100A 120A 160A 200A Hypertherm 45A 65A 85A 105A 125A 200A Cutting thickness According to the plasma power source Height regulating device Arc voltage height Cutting speed 0-10000mm/min Cutting precision ±0.3mm Control ccuracy ±0.01mm Support software Fastcam /Type3/autocad/pro/CAXA etc. Working Temperature -5~60°CRelative Humidity, 0-95%. Power Supply Voltage 380V±20%(220V optional,but we need custom for you) Packing Weight 3900x2300x1750mm Packing Size 1500kg
Plasma Cutting Machine
Plasma Cutting Machine,Cnc Plasma Cutting Machine,Plasma Flame Cutting Machine,Plasma Cutter
Shandong U-May CNC Technology Co., Ltd. , https://www.fiberlasers.de
没有评论:
发表评论